Hi,
I'm running Smart RF studio on Win 8.1 which is quest in Virtualbox.
I'm not able to use two CC-Debuggers simultaneously. only device which is connected first is usable. Smart RF studio shows that only one device is connected. Both debuggers can be used independently and also together with Smart RF Flash programmer.
Can someone confirm that it is possible to use multiple CC-Debuggers with same type of SoC in Smart RF studio?
After using CC1101 on projects at work I want to to buy a dev board and dig deeper into the low level features of TI RF chips I was about to buy a
CC1120 Development Kit as it includes a MSP430 Debug jtag then came the big turnoff
This kit requires IAR EW . As a former TI employee and avid fan of CCS I was flabbergasted it didn't include CCS support for MSP
If I had a dime for every kit I bought for either WIFI or Blue Tooth used IAR and when I bought it the code size limited feature of IAR prohibited me from doing anything REAL I'd be rich
Come on TI you must have have a MSP based kit(8051 ARRRRRG) that uses CCS
I already have a 2540/60 based kit that supports CCS and TI-RTOS the problem is the Bluetooth overhead is too much of a slope
My goal is to 6LOWPAN or RFMESH using all TI hardware(CCXXXXX+TI Micro) and CCS software . TI is the industry leader and provides CCS free versions that are not size limited for ARM or am I mistaken
I don't want to wade through another dev kit starter guide and get disappointed again
Can anyone tell me if the beast I seek exists ?
Hi, I have a circuit with a CC2530 and a CC2590 implemented. When i use my implemented embedded radio FW to control the radio, the performance is alright when looking at range and packet loss. I would then use the SmartRF Studio to measure the number of packets received and using a spectrum analyser testing the maximum output performance.
Unfortunately I am experiencing that the output is approximately 40dBm below the measured output with my implemented embedded radio FW. I tried setting a breakpoint in IAR at the point of transmit, so I could see the radio registers and GPIOs.
I have tried the exact same values in Smart RF Studio, but the result is the same, I still measure 40dBm less.
What am I doing wrong? Please open my config file.
(Please visit the site to view this file)
Here is a snip of my schematic, I know that it is not the GPIOs from the evaluation design, but that should not make any difference!? At least it doesn't with my implemented embedded FW.
BR,
Simon
We are making use Devpack debugger(XDS110) for cc2640 using Simple Ble peripheral examples.While debugging we are stucked with this error, can anyone suggest me in resolving this error.
Thanks nd Regards
sagar S
Hi people,
I am having an issue on compiling the demo programs from TI to program my SmartRF05 board. For the PER test demo, I saw that the hal_board.h file has configurations for specific SoC type. I also saw mine(CC2530) is listed there, however, IAR is still complaining about not supporting the chip. Anyone had this issue before.
PS: the variable is named 'chip' on hal_board.h but I couldn't find any line in the whole project file of PER demo, to set it to 'CC2530'.
Edit: The following is a code fragment from "hal_board.h". So, the question can be narrowed to, where do you set the chip variable 'chip' to your specific board?
#if (chip==2430)
#include "ioCC2430.h"
#elif (chip==2431)
#include "ioCC2431.h"
#elif (chip==2530 || chip==2531)
#include "ioCC2530.h"
#elif (chip==2510)
#include "ioCC2510.h"
#elif (chip==2511)
#include "ioCC2511.h"
#elif (chip==1110)
#include "ioCC1110.h"
#elif (chip==1111)
#include "ioCC1111.h"
#else
#error "Chip not supported!"
#endif
Cheers,
Dear Fellows,
I am working with the CC430F5137 micro-controller in an OLIMEX MSP430-CCRF board. Additionally, I dispose of the MSP-FET430UIF to debug and flash the board. When I connect the debugger to my Linux machine, it uses only the ttyACM0 port, fact that doesn't allow me to establish a bidirectional communication between the PC to the Launchpad. Then, I can not settle an UART communication to print the current status of the program I flashed into the Launchpad.
After reviewing the documentation provided by TI, the debugger does not have TXD/RXD pins.
How can I make the C's printfs using the JTAG?
Regards,
jacevedo
Hi,
I got today a CC Debugger and had problems installing it in a brand new Lenovo W550s running Windows 7 Pro that has already installed CCSv6, SmartRF Tool, BTool and the like. I am getting the Unknown Device error with Code 29. I tried 2.0 and 3.0 ports to no avail. I re-installed the drivers (v1.2.0), nothing. All the other stuff runs fine: SmartRF06, XDS200, USBCC2540 dongle.
Of course I tried all the tricks already (DN304 included). All looks ok. Now, to see if there was any problem with the CC debugger itself (which, BTW, when I connected it to the CC2540 dongle and to any of the USB ports it shows a green light, as the CC2540 does too, thus indicating the dongle was recognized properly) I tried connecting it to my main machine running Linux and having Windows 7 virtualized: Windows does not get any indication of the CC Debugger been connected at all and when I look the output from dmesg it shows this:
[ 253.808558] usb 1-10: new full-speed USB device number 12 using xhci_hcd
[ 253.920659] usb 1-10: device descriptor read/64, error -71
[ 254.136842] usb 1-10: device descriptor read/64, error -71
[ 254.353036] usb 1-10: new full-speed USB device number 13 using xhci_hcd
[ 254.465155] usb 1-10: device descriptor read/64, error -71
[ 254.681304] usb 1-10: device descriptor read/64, error -71
[ 254.897469] usb 1-10: new full-speed USB device number 14 using xhci_hcd
[ 254.897566] usb 1-10: Device not responding to setup address.
[ 255.101758] usb 1-10: Device not responding to setup address.
[ 255.305828] usb 1-10: device not accepting address 14, error -71
[ 255.417925] usb 1-10: new full-speed USB device number 15 using xhci_hcd
[ 255.418036] usb 1-10: Device not responding to setup address.
[ 255.622205] usb 1-10: Device not responding to setup address.
[ 255.826271] usb 1-10: device not accepting address 15, error -71
[ 255.826313] usb usb1-port10: unable to enumerate USB device
It looks like there is something wrong with the CC Debugger, that message is sometimes associated with a current higher than the port can provide.
Any thoughts? Thanks.
Pibe
Hello.
I'd like to know if CC Debugger (including SOC-BB board) can be used in combination with CC1120EMK-169 modules, e.g. for RX/TX testing with Smart RF Studio or Packet Sniffer.
Thank you in advance.
Regards,
Peppe
Hi,
From Zstack_API.pdf I came to know that from ZMacSetTransmitPower() i can change the power of the radio
But i want to know that
with TX_PWR_MINUS_22 what will be the max range between two device
same for TX_PWR_MINUS_21 etc....
i am using cc2538 controller for my zigbee applications
thanks in advance
sibin
Hi, I'm having troubles with the cc1310 development kit. One of the SMARTRF06EBK is not working, SN:0x1025F.
After following the instructions of the quick start guide of the CC1310 EM the screen show nothing, while the other SMARTRF06EBK work as expected. Have interchanged the CC1310EM and the SMARTRF06EBK, and both CC1310EM works on the not faulty. Have checked the configuration switches and both boards are the same.
By visual inspection, i couldn't find any misaligned component or fabrication mistake.
The board was tested first with 2 AAA batteries, and after that, with usb power supply. When plugged on the pc, the XDS100v3 is correctly recognized, as well as the serial port. But the screen keep showing nothing.
What should i do? maybe some firmware update needed?
regards, Pablo
Hi,
It seems text view works strange in Paket RX tab. Please see screenshots below. Both represent view for the same TX packets.
If I remove check-box "Seq. number included in payload" I can't see text.
[?] SmartRF06 EM connector part number (RF1, RF2 -> SMD_HEADER_2X10)
i am trying to find out what is the part number for it?
is it TFML or TFM? and for the LEAD Type -> it has option of "-02", "-12", "-22", "-32",: are those the connector height or pin height?
i would like to be able mate with CC1310 module which is (SFM-110-02-S-D-A-K-TR)
we are testing our hardware for cc2650 with cc2592 . so adding cc2592 pins in code we are getting some packets on packet sniffer for 1 meter range and also adding cc2592 in code we are getting same range basically it seems like cc2592 is not working correct how can we assure that our firmware is correct. any help will be appreciated.
hi support,
I can set and red reg correctly, also I can burst write data into tx fifo, once I excuted stx, I can see it is set correctly from status returning. but two problems:
1) the value of txbytes keeps increasing, it looks not get sent out.
2) I checked MARCSTAT, it looks radio goes into rx mode.
as a result, I can not receive the data from receiver.
sres,execute cmd strobe 0x30, return 0xFF
read reg 0x02, value is 0x3F
read reg 0x03, value is 0x07
read reg 0x08, value is 0x45
read reg 0x0B, value is 0x0F
read reg 0x0D, value is 0x1E
read reg 0x0E, value is 0xC4
read reg 0x0F, value is 0xEC
read reg 0x10, value is 0x8C
read reg 0x11, value is 0x22
read reg 0x12, value is 0x02
read reg 0x15, value is 0x47
read reg 0x18, value is 0x04
read reg 0x19, value is 0x76
read reg 0x20, value is 0xF8
read reg 0x23, value is 0xA9
read reg 0x24, value is 0x0A
read reg 0x25, value is 0x20
read reg 0x26, value is 0x0D
read reg 0x2C, value is 0x88
read reg 0x2D, value is 0x31
read reg 0x2E, value is 0x0B
read done
write reg 0x02, value is0x06
write reg 0x03, value is0x47
write reg 0x08, value is0x05
write reg 0x0B, value is0x06
write reg 0x0D, value is0x10
write reg 0x0E, value is0xA7
write reg 0x0F, value is0x62
write reg 0x10, value is0xF5
write reg 0x11, value is0x83
write reg 0x12, value is0x13
write reg 0x15, value is0x15
write reg 0x18, value is0x18
write reg 0x19, value is0x16
write reg 0x20, value is0xFB
write reg 0x23, value is0xE9
write reg 0x24, value is0x2A
write reg 0x25, value is0x00
write reg 0x26, value is0x1F
write reg 0x2C, value is0x81
write reg 0x2D, value is0x35
write reg 0x2E, value is0x09
write patable 0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
write done
read reg 0x02, value is 0x06
read reg 0x03, value is 0x47
read reg 0x08, value is 0x05
read reg 0x0B, value is 0x06
read reg 0x0D, value is 0x10
read reg 0x0E, value is 0xA7
read reg 0x0F, value is 0x62
read reg 0x10, value is 0xF5
read reg 0x11, value is 0x83
read reg 0x12, value is 0x13
read reg 0x15, value is 0x15
read reg 0x18, value is 0x18
read reg 0x19, value is 0x16
read reg 0x20, value is 0xFB
read reg 0x23, value is 0xE9
read reg 0x24, value is 0x2A
read reg 0x25, value is 0x00
read reg 0x26, value is 0x1F
read reg 0x2C, value is 0x81
read reg 0x2D, value is 0x35
read reg 0x2E, value is 0x09
read after writing done
send start-----------------------------
read MARCSTATE first
read reg 0x35, value is 0x01
sidle,execute cmd strobe 0x36, return 0x0F
read version
read reg 0x31, value is 0x14
read PARTNUM
read reg 0x30, value is 0x00
read LQI
read reg 0x33, value is 0x7F
read txbytes first time
read reg 0x3A, value is 0x00
read txbytes second time before write fifo
read reg 0x3A, value is 0x00
write tx fifo 0x17,0x0C,0x0D,0x0E,0x0F,0x10,0x11,0x12,0x13,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
read txbytes first time after write fifo but before stx
read reg 0x3A, value is 0x18
stx,execute cmd strobe 0x35, return 0x0F
read MARCSTATE after stx
read reg 0x35, value is 0x13
read txbytes first time after stx
read reg 0x3A, value is 0x16
send end--------------------------------------
send start-----------------------------
read MARCSTATE first
read reg 0x35, value is 0x13
sidle,execute cmd strobe 0x36, return 0x2F
read version
read reg 0x31, value is 0x14
read PARTNUM
read reg 0x30, value is 0x00
read LQI
read reg 0x33, value is 0x7F
read txbytes first time
read reg 0x3A, value is 0x0B
read txbytes second time before write fifo
read reg 0x3A, value is 0x0B
write tx fifo 0x17,0x0C,0x0D,0x0E,0x0F,0x10,0x11,0x12,0x13,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
read txbytes first time after write fifo but before stx
read reg 0x3A, value is 0x23
stx,execute cmd strobe 0x35, return 0x5F
read MARCSTATE after stx
read reg 0x35, value is 0x13
read txbytes first time after stx
read reg 0x3A, value is 0x22
send end--------------------------------------
send start-----------------------------
read MARCSTATE first
read reg 0x35, value is 0x13
sidle,execute cmd strobe 0x36, return 0x2F
read version
read reg 0x31, value is 0x14
read PARTNUM
read reg 0x30, value is 0x00
read LQI
read reg 0x33, value is 0x7F
read txbytes first time
read reg 0x3A, value is 0x22
read txbytes second time before write fifo
read reg 0x3A, value is 0x22
write tx fifo 0x17,0x0C,0x0D,0x0E,0x0F,0x10,0x11,0x12,0x13,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
read txbytes first time after write fifo but before stx
read reg 0x3A, value is 0x3A
stx,execute cmd strobe 0x35, return 0x56
read MARCSTATE after stx
read reg 0x35, value is 0x13
read txbytes first time after stx
read reg 0x3A, value is 0x39
send end--------------------------------------
I want to connect CC2531 dongle to the BeagleBone Black. BeagleBone runs on Linux (Debian). Now I am in need of cc2531 driver for Beagle Bone.
I Downloaded the "Z-Stack_Linux_Gateway_1_0_1_installer" But its for Computer running with the Linux (32 or 64bit os).
Can any one please share me the driver for cc2531 or guide me on how to work with this dongle by connecting it to Beagle Bone.
Hi,
First of all, sorry if my English is not perfect. It's not my mother tongue.
I try to connect a RF-BM-S02 Bluetooth module to CC Debugger but the light stay red. This module use CC2540/41 ( mine use CC2541 ).
I have checked the connection between us and all signals are at the right place and I have not forgotten to connect 3.3V on pin 9 and pin 2 on the debugger.
I have updated the firmware ( 0044 ). BLE module is visible when I make bluetooth scan.
I don't know why CC Debugger don't recognize BLE module.
Is anyone ever had this problem ?
Thanks in advance.
RF-BM-S02 datasheet :
hello ,everyone
i would like to know:
can i add Bluetooth support to any integrated rfid reader ?
recently i help purchase a batch of uhf integrated rfid readers syncotek.com/.../uhf_integrated_reader_1.html, and i want to add Bluetooth.
Can i ?
How can i do it if it is possible?
hi
i want to use asm("nop") in my sample application ZStack-CC2530-2.5.1a, can i know how many asm(nop) i need to get 1us or in anothor way can i know what is the clock frequency of my cpu , because i don't think it's 32MHZ
'm trying to read the temperature value from DHT so i have to respect the time limits which are required to get the correct value, so to make the sensor start i have to give it one on the data port for 18ms and wait between 20-40 us so i tried to use asm("nop") instruction to get these periods, but still not working